isaleCAD Water Transmission Line Design Software

isaleCAD

WATER TRANSMISSION LINE DESIGN SOFTWARE
For Drawing/Modelling/Planning/Design/Analyze

 

AnkiSOFT Software developes software to design infrastructure projects. isaleCAD has been developed for water transmission line design. It is for drawing/modelling/planning/design/analyze the water transmission line. The software works under AutoCAD or ZWCAD.

AnkiSOFT Software – isaleCAD – Water Transmission Line Design Software - Software Menu

AnkiSOFT SoftwareisaleCAD – Water Transmission Line Design Software – Menu of the Software

DRAWING the NETWORK

It is possible to arrange the drawing style by using STYLE MANAGER, so you can use different drawing style in different projects.

OPEN LAYER command can open all the necessary layers that the software needs.

You can define/draw/edit/delete/move Station nodes/Keeper nodes (SK), can change some/all properties of SKs. The software will write; SKno and the elevation for each SK on the drawing.

You can find any SK by searching the SKno, can change the location of SKno, can renumber some/all SKs from a specified number.

You can define/draw/edit/delete pipes, can change the direction of pipes, can change some/all properties of pipes.

You can define/draw/delete air-releasing-valve/water-drain-valve to any SK. You can renumber them.

 

Water Transmission Line Software - Line Model

Water Transmission Line – Line Model

ERROR CHECKING

You can check weather there is any mistake in the network model. You can find and you can correct them.

Such as; same SKnos, pipe connections from/to SKs.

HYDRAULIC DESIGN

During design works; all the information on the drawing will be send to calculation, the calculation software will do hydraulic calculations, then all the calculated information will be send back to the drawing to show the final situation.

You can repeat this process, until you reached to the situation that you want.

DESIGN CRITERION

You can define;

Water supply point can be; pump-station, embedded-reservoir, elevated-reservoir or pressure-decreasing-valve
Water destination point can be; embedded-reservoir, elevated-reservoir, pressure-decreasing-valve, network enterance node or water-drain-valve
Profile drawing height
You can decide air-releasing-valve/water-drain-valve, or software will decide them itself, or software and you can decide together
The software will decide vertical curve fittings automatically
If the pipe slope is greater than or equal to 30%, software will add backfill-supporting-wall automatically
Curve angles can be in degree/grad
Pressure calculations can be according to pipe bottom elevation or pipe center elevation
The output is in DXF file format
For each Type-DIAMETER; type-name, material (concrete, reinforced concrete, PVC, ACB, Steel, Cast iron, Ductile iron, HDPE, CTP, …), allowable pressure, wall thickness, inner diameter, pipe discharge, design formula (William-Hazen, Ludin, …), “C” values for the formula, outer diameter and basement layer thickness.

DESIGN CALCULATION TABLES

Hydraulic calculations are in the form of tables and recorded in a text file. In the first table;

SKno
Distance from the beginning
Ground elevation
Pipe elevation
Total JL
Total local head loss (LK)
Total JL+LK
Piesometric elevation
Pressure during operation
Maximum pressure
Minimum pressure.

In the second table;

SKno
Air-releasing-valve/water-drain-valve name
Angle of horizontal curve
Angle of vertical curve
Angle of 3D curve.

PROFILE

The information on the profile is;

Excavation depth
SKno
Ground elevation
Pipe center/bottom elevation
Distance between SKs
Distance from the beginning
Pipe diameter and material type
Slope
Direction on the plan. All of them will be prepared automatically.

 

Water Transmission Line - Profile (Pressurized Line)

Water Transmission Line – Profile (Pressurized Line)

 

Water Transmission Line - Profile (Gravity Line)

Water Transmission Line – Profile (Gravity Line)

 

Water Transmission Line - Profile (Gravity Line)

Water Transmission Line – Profile (Gravity Line)

SCHEMATICAL PROFILE

The information on the profile is;

Maximum pressure line
Piesometric line
Static line
Minimum pressure line
SKno
Pipe center/bottom elevation
Distance between SKs
Distance from the beginning
Pressure during operation
Maximum and minimum pressure during water hammer
Static pressure
Pipe diameter and material type. All of them will be prepared automatically.

 

Water Transmission Line - Schematic Profile (Pressurized Line)

Water Transmission Line – Schematic Profile (Pressurized Line)

 

Water Transmission Line - Schematic Profile (Gravity Line)

Water Transmission Line – Schematic Profile (Gravity Line)

 

Water Transmission Line - Schematic Profile (Gravity Line)

Water Transmission Line – Schematic Profile (Gravity Line)

INFORMATION TRANSFER

You can transfer easily all the network information to another drawing/computer, or vice versa.

GENERAL

There is no limit to the number of SKs and pipes.
There is no limit to the number of pipe diameters and pipe materials.
It is possible to have more than one transmission line on the same drawing. There is no limit to the number of transmission line.
During design works; the software can show the logical mistakes of the transmission line to the user to correct them.
On the schematic profile; you can see the SKs having pressure less than minimum-operational-pressure and having pressure above the maximum-static-pressure.
You can renumber SK numbers automatically.
All calculations are in a text file, in the form of tables. You can open, you can copy, you can print directly at any time.
You can use our software commands with AutoCAD or ZWCAD commands too.

UPGRADE HISTORY

JANUARY.2018

AutoCAD 2018 x64, ZWCAD 2018 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

MAY.2017

AutoCAD 2017 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

JANUARY.2015

AutoCAD 2015 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

JANUARY.2013

AutoCAD 2013 x64
Windows7 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

JUNE.2012

Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

JANUARY.2012

Windows7 x32
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

JANUARY.2010

WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

JANUARY.2009

WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

JANUARY.2003

WindowsXP x32

JANUARY.1999

Windows98

JANUARY.1997

ACAD 14
Windows98

JANUARY.1988

MSDOS